junaid rasheed

 Being as a QC INSPECTOR ELECTRICAL, to support YASREF electrical inspection department with quality as per Aramco and YASREF standards and procedures during the MEGA TURNAROUND 2024 PROJECT,
 Witness the all activities of the testing and preventive maintenance at the substations inside and outside, for electrical equipment’s such as LV & MV SWTCHEARS, LV & MV MOTOR CONTRL CENTERS, TRANSFORMERS, NGR, RMCC’S, CATHODIC PROTECTION SYSTEMS.
 Witness of the MOTOR SOLO RUN TEST,
 Cable testing of the MV cables PARTIAL DICHARGE.

 Being an E&I QC INSPECTOR, the role is to provide strong leadership & Supervision of ELECTRICAL activities assure health & safety environment, support engineering team, dealing with owner engineer (O.E) coordination and communication with vendors and multidiscipline professionals.
 According to Specification and inspections Procedures of Quality Control, Inspection and test plan of all electrical equipment in accordance to assist in updating Operations Function codes, standards and procedure in ELECTRICAL.
 Attended the minutes of meeting with Client, supported in smooth progress at site, on site guidance to construction people during execution as per site specification and client satisfaction.
 Checking, Verification and Testing of fabrication, construction and installation work perform in order to confirm that the applicable rule, code and standard are being meet and that the project requirements.
 Prepare the monthly running invoice as per bill of quantity (BOQ) electrical, instrument and telecommunication work and submit to client for verification and approval.
 Familiar with International standards: IEEE, NFPA, NEC, NEMA and other, Co-ordination with client’s project inspection unit for project inspections & stage wise activities for Hold/ Witness/ Surveillance/ Monitor and review points.
 Responsible for the material receiving inspection as per approved documents like material approval, purchase orders, certificate of conformance, Inspection release note, vendor documents, approved drawings, Project Specification and others related documents.
 Material receiving inspection of the RIGID PVC and STEEL conduits, Cable ladder Hot Dip Galvanized Carbon Steel with complete accessories, lighting fixtures.
 Material receiving inspection of the E-house with installed Air insulated LV and MV switchgear Substation lv Motor Control centers, Small Power DB’s, neutral earthing resister of power transformer.
 Material receiving inspection of the medium voltage (MV), Low voltage (LV), Telecom and instrument cables.
 Inspection and testing of the complete earthing system with branch, main grounding mesh, substations, earthing pit with earth rod and bus bar, under and above ground earthing, cable laying, cad welding, bus bar installation indoor and outdoor on wall and steel structure, as per approved drawing, typical installation drawing and project specification. Inspection and testing of the earthing mesh with digital earth tester and keep the record.
 Complete installation and Inspection of the main power distribution transformer 33kv/11KV 40 MVA, distribution transformer 2MVA 11KV/0.42KV and variable frequency drive transformers 17 MVA 11KV/6KV and variable frequency drive panels 6 KV, substation E-house with complete installation of the MV and LV switchgears and panels, distribution boards, Main AC DC Distribution Board, Control panel, MCC and MV, LV Bus duct.
 Inspection of the hot dip galvanized cable trays with complete accessories, different type of the cable tray supports on steel structures and concrete wall mounted, GI conduit, Rigid PVC, PVC conduit above and underground as per standard and project specifications.
 Inspection of the Lightning protection system for buildings as per approved IFC drawing and project specification.
 Cable Tray / Conduit / Trench Installation, Instrument cables meggering and continuity check, electrical Cable
Laying, Data cables laying, glanding and termination.

 As a QC INSPECTOR ELECTRICAL Installation of the LAN cabinet, BUILDING ENTERENCE PROTECTOR (BEP) cabinet, cable runways, metallic conduits, structure cabling system (SCS), splice closer for 25 PR copper cable, 25 PR copper cable laying, glanding, dressing and termination.
 Installation of the Fiber optic cable (single mode or multi-mode) pulling, laying, dressing, glanding with complete installation of cable runway, conduits.
 Installation of UTP CAT 6 cable runways, conduits, outlets, ports, cable pulling, laying, dressing, glanding with complete installation of IP and ANALOG TELEPHONES.
 Monitor the Termination and testing of UTP CAT 6 cables with EXFO MAX TESTER MAX-635.
 Installation of the Grounding and Bonding for cable runways, conduits, LAN Cabinets, building entrance protector, splice closer.
 Installation of the Telecommunication Main Grounding Bus bar (TMGB), with complete accessories.
 Installation of the IT & NON-IT pedestal, grounding, tagging of the sub duct install with white plug and blind plug, grounding of the pedestal guard and tagging by stencil.
 Installation of the indoor IPCS hand set station with all equipment’s cable trays, conduits, cable pulling, glanding, dressing, termination and as per drawing and specification. Coordination with QC for Inspection of the indoor hand set station, all equipment’s and cable testing.
 Installation of the outdoor handset station with all equipment (EXPLOSION PROOF).
 Complete installation of the grounding cable laying, dressing, glanding and termination at indoor and outdoor IPCS HAND SET STATION and all equipment as per standard and drawing.
 Final testing of the IN-PLANT COMMUNICATION SYSTEM, with vendor, Saudi Aramco operation team with complete voice paging in LOOP A and B, indoor and outdoor.

 As a QA/QC INSPECTOR ELECTRICAL Installation and inspection of the 380kV Gas Insulated Switchgear with complete indoor and outdoor equipment.
 Installation and inspection of the shunt reactors 80 and 120MVA with hybrid GIS, auxiliary transformers, ring main unit, MV LV SWGR.
 Obtain necessary Drawings & documentation prepares required materials, allocate jobs and actively participate and supervise the job completion.
 Perform incoming material inspection based on approved drawings, Project Specification and P.O.
 Extra High Voltage (EHV), Medium voltage (MV), Low voltage (LV), Telecom, Instrument cable, shielded and communication interface cables testing laying, routing, glanding & termination according to Cable schedule and termination drawing.
 Installation and Testing of Switch gears (MV & LV), Main AC DC Distribution Board, Control panel, MCC, Transformers, Lighting fixtures, Welding receptacles, local control station and Lightning Protection system.
 Installation and inspection of Generator step-up transformer (GSUT), Unit auxiliary transformer (UAT) and Common auxiliary transformer (CAT).
 Installation and inspection of Isolated phase bus duct (IPB), none segregated phase bus duct (NSPB), Segregated phase bus duct (SPB).
 Site surveillance of the Fabrication and Installation of cable tray support, lighting fixture support, Speaker support, Junction box support, Instrument stanchions, Trays, conduits, Battery racks and Battery etc.,
 Installation inspection and testing of Earthing system which includes under and above ground earthing, cable laying, cad welding, earthing electrode installation.
 Installation, Testing of Impressed Current Cathodic Protection (ICCP) for 32” Underground pipe line and Sacrificed Anode Cathodic Protection (SACP) for underground road crossing pipe lines.
 Implement safety and quality of works to ensure guaranteed services and satisfaction of Client.
 Responsible for Mechanical Completions of various Systems like Power, ESD, DCS and Fire & Gas by using HHI PLANT PCS (Project Control System), PROJECT MANAGEMENT INFORMATION SYSTEM. (PMIS) and SITE PEROS.

 As a QA/QC ELECTRICAL ENGINEER Installation, inspection of polypropylene and polyethylene plant, cable trays, motors, transport conveyors, photo cells, limit switches.
 Monitoring and executing of Plant installation activities in accordance with the Project Specifications, Industry Standards and Guidelines.
 Check cable termination of power and control cable base on cable schedule and termination drawing.
 Coordinating with construction team for assuring quality to meet with client requirements and take initiate remedial or corrective action based on codes and standards and verify the closure of NCR and Punch List clearing activities.
 Competency to issue Non-Conformance Reports (NCR) with respect to Electrical jobs to sub-contractor and/or vendor personal for rectification. Tracking, corrective action and close out of NCR’s.
 Involved the Quality walk-through with third party inspector and client for generating punch points.
 Coordinating the Punch List Clearance of each subsystem prior to hand over to commissioning department.
 Develop inspection records, punch list, mechanical completion packages and final dossiers.
 All E&I Cable pulling, cable ladders/conduit installations JB and terminations, tubing/air supply piping installations, field instruments installation.
 Installation, inspection and maintenance of polypropylene and polyethylene plant, cable trays, motors, transport conveyors, photo cells, limit switches.
 Check cable termination of power and control cable base on cable schedule and termination drawing.